IN-STOCK SHELVES AND COUNTERTOPS WILL SHIP WITHIN 1-2 DAYS. DISCOUNT CODES FOR YOUR CHECKOUT ARE HERE.

stainlesssteelspace

British Stainless Steel Association (BSSA) recommends :

Requirement

Suggested Method 

Comments

1.Routine cleaning of light soiling

Soap, detergent or dilute (1%) ammonia solution in warm clean water. Apply with a clean sponge, soft cloth or soft-fibrebrush then rinse in clean water and dry

Satisfactory on most surfaces

2.FingerprintsNancy's photo

Detergent and warm water, alternatively, hydrocarbon solvent 

to clean stainless steel

Proprietary spray-applied polishes available to clean and minimise remarking

 

3.Oil and grease marks

Hydrocarbon solvents (methylated spirit, isopropyl alcohol or acetone)

Alkaline formulations are also available with surfactant additions e.g.'D7' Polish

4.Stubborn spots, stains and light discolouration. Water marking. Light rust staining

Mild, non-scratching creams and polishes. Apply with soft cloth or soft sponge and rinse off residues with clean water and dry.

Avoid cleaning pastes with abrasive additions. Suitable cream cleansers are available with soft calcium carbonate additions, e.g. 'Jif', or with the addition of citric acid, e.g. Shiny Sinks. Do not use chloride solutions.

5.Localised rust stains caused by carbon steel contamination

Proprietary gels, or 10% phosphoric acid solution (followed by ammonia and water rinses), or oxalic acid solution (followed by water rinse).

Small areas may be treated with a rubbing block comprising fine abrasive in a hard rubber or plastic filler. Carbon steel wool should not be used, nor should pads that have previously been used on carbon steel. A test should be carried out to ensure that the original surface finish is not damaged.

6.Burnt on food or carbon deposits

Pre-soak in hot water with detergent or ammonia solution. Remove deposits with nylon brush and fine scouring powder if necessary. Repeat if necessary and finish with 'routine cleaning'.

Abrasive souring powder can leave scratch marks on polished surfaces.

7.Tannin (tea) stains and oily deposits in coffee urns

Tannin stains - soak in a hot solution of washing soda i.e. sodium carbonate. Coffee deposits - soak in a hot solution of baking soda (sodium bicarbonate).

These solutions can also be applied with a soft cloth or sponge. Rinse with clean water. Satisfactory on most surfaces.

8.Adherent hard water scales and mortar/cement splashes

10-15 volume % solution of phosphoric acid. Use warm, neutralise with dilute ammonia solution, rinse with clean water and dry6. Alternatively soak in a 25% vinegar solution and use a nylon brush to remove deposits.

Proprietary formulations available with surfactant additions. Take special care when using hydrochloric acid based mortar removers .

9.Heating or heavy discolouration

a) Non-scratching cream or polish e.g. Solvol Auto Chrome Metal Polish  

b) Nylon-type pad, e.g. 'Scotchbrite'

a)Creams are suitable for most finishes, but only use 'Solvol' on bright polished surfaces. Some slight scratching can be left. 

b)Use on brushed and polished finishes along the grain.

10.Badly neglected surfaces with accumulated grime deposits

A fine, abrasive paste as used for car body refinishing, e.g. 'T-cut' rinsed clean to remove all paste material and dried.

May brighten dull finishes. To avoid a patchy appearance, the whole surface may need to be treated.

11.Paint, graffiti

Proprietary alkaline or solvent paint strippers, depending upon paint type. Use soft nylon or bristle brush on patterned surfaces.

Apply as directed by manufacturer.


Newer Post


10 comments

  • Hi Robin,
    Yes, stainless steel only,
    brushed finishing to be make scratches less visible.
    You can see the most effective method of removing
    scratches on stainless steel surface here :

    www.youtube.com/watch?v=FOmUran35dE

    Regards,
    Ponoma team

    Ponoma team

  • Hi,
    The shelves look great.
    Are they solid metal?
    Do they scratch easily?
    Please let me know; thanks

    Best,
    Robin Clark

    Robin Clark

  • Glad to hear it , Nancy!
    Thank you for your feadback.

    Ponoma team

  • Many thanks for your recommendations and this link too:
    My stainless shelf is shining again without any fingerprints !!!

    Nancy

    Nancy

  • Hi,
    Do you have photos of the underside of the shelf? Is the underside of the shelf seamless or does it show the seam where the stainless steel is wrapped?‘m interested in ordering your shelves but would like to see the differences between 1.5" and 2" thickness. I’ll likely order 42″×10″ and 26″×10″ lengths. Would you have any photos showing shelves with different thickness?
    Thanks.

    Bao Chang


  • 1
  • 2

Leave a Comment

Please note, comments must be approved before they are published